Sonsivri
 
*
Welcome, Guest. Please login or register.
Did you miss your activation email?
December 23, 2024, 10:00:57 10:00


Login with username, password and session length


Pages: [1]
Print
Author Topic: AT89C55WD programmer  (Read 5263 times)
0 Members and 1 Guest are viewing this topic.
mr_byte31
Hero Member
*****
Offline Offline

Posts: 600

Thank You
-Given: 75
-Receive: 144



« on: February 05, 2018, 10:50:40 10:50 »

Hi All,

I am looking for a simple programmer for AT89C55WD so I can build it.
I searched the internet but couldn't reach any valuable information. there is only one programmer at microchip website which is really expensive to me.
I also found a parallel programmer on internet but my PC doesn't support this interface anymore.
any suggestions ?
Logged

Do not trifle with the Moderators , as you are small, and crunchy, and taste good with ketchup.
pickit2
Moderator
Hero Member
*****
Offline Offline

Posts: 4671

Thank You
-Given: 836
-Receive: 4330


There is no evidence that I muted SoNsIvRi


« Reply #1 on: February 05, 2018, 02:00:14 14:00 »

the MiniPro TL866 is cheap
Logged

Note: I stoped Muteing bad members OK I now put thier account in sleep mode
mr_byte31
Hero Member
*****
Offline Offline

Posts: 600

Thank You
-Given: 75
-Receive: 144



« Reply #2 on: February 13, 2018, 02:09:56 14:09 »

making the circuit will be much cheaper !
did you try any circuits for this controller?
Logged

Do not trifle with the Moderators , as you are small, and crunchy, and taste good with ketchup.
kayvee
Active Member
***
Offline Offline

Posts: 172

Thank You
-Given: 98
-Receive: 101


« Reply #3 on: February 13, 2018, 03:11:25 15:11 »

I'd agree with pickit2, the MiniPro is a good way to go.

Then you can use it on any other future project that comes along.
Logged
pickit2
Moderator
Hero Member
*****
Offline Offline

Posts: 4671

Thank You
-Given: 836
-Receive: 4330


There is no evidence that I muted SoNsIvRi


« Reply #4 on: February 13, 2018, 04:35:16 16:35 »

Quote from: mr_byte31
making the circuit will be much cheaper !
did you try any circuits for this controller?
Why ?
It is cheaper to buy the MiniPro TL866cs and upgrade it to TL866A
plus you get all the adapters thrown in.
Logged

Note: I stoped Muteing bad members OK I now put thier account in sleep mode
towlerg
Senior Member
****
Offline Offline

Posts: 263

Thank You
-Given: 474
-Receive: 104

What is this for?


« Reply #5 on: February 13, 2018, 06:50:47 18:50 »

Whats the difference between TL886cs and TL866A, seem the same on aliexpress.com?

The only supported device I could finf did not include any of the 18FxxKxx series, did I miss something?
Logged

Win 7 Ult x64 SP1 on HP2570p
sphinx
Hero Member
*****
Offline Offline

Posts: 920

Thank You
-Given: 615
-Receive: 272



« Reply #6 on: February 13, 2018, 07:50:13 19:50 »

the TL866A has a icsp port TL866CS does not, but is upgradeable to a TL866A if wanted to do
some extra work to change firmware and adding a icsp connector.
Logged

laws of physics are not laws at all, just assumptions and formulas that work as long as we don't figure something new that wrecks the calculations. the infinite onion try to peel that one
pickit2
Moderator
Hero Member
*****
Offline Offline

Posts: 4671

Thank You
-Given: 836
-Receive: 4330


There is no evidence that I muted SoNsIvRi


« Reply #7 on: February 14, 2018, 10:57:35 10:57 »

The only supported device I could finf did not include any of the 18FxxKxx series, did I miss something?
The 18FxxJxx and 18xxKxx are programed the same way. the K devices are just newer.
But then you do have a Pic Programmer, don't you. if your using Pic devices other than just the one off.

For a list of devices is here. Note: there maybe a newer list of devices. wink or add your own devices, if you know where to look.
http://www.autoelectric.cn/minipro/miniprosupportlist.txt
« Last Edit: February 14, 2018, 11:01:29 11:01 by pickit2 » Logged

Note: I stoped Muteing bad members OK I now put thier account in sleep mode
towlerg
Senior Member
****
Offline Offline

Posts: 263

Thank You
-Given: 474
-Receive: 104

What is this for?


« Reply #8 on: February 14, 2018, 03:37:58 15:37 »

Quote
The 18FxxJxx and 18xxKxx are programed the same way. the K devices are just newer.
I guess that true in principle (modified SPI) it doesn't seem to be true in detail. In their infinite wisdom, Microchip have issued separate programming specs for the J and K series.

I have bought a Pickit3 specifically because it claims to support 18F26K42. If I could find a PK2DeviceFile.dat with 18F26K42 (although I did find for 18F26K22) I'd stick with my trusty Pickit2.
Logged

Win 7 Ult x64 SP1 on HP2570p
Yukine
Inactive

Offline Offline

Posts: 6

Thank You
-Given: 19
-Receive: 17


« Reply #9 on: February 17, 2018, 04:31:03 16:31 »

just asking, why are you using a 89c55

also, this one seems simple enough to build (this should work with a serial <-> usb converter)
http://www.shrubbery.net/~heas/willem/8051-avr2/index-9.htm
Logged
Pages: [1]
Print
Jump to:  


DISCLAIMER
WE DONT HOST ANY ILLEGAL FILES ON THE SERVER
USE CONTACT US TO REPORT ILLEGAL FILES
ADMINISTRATORS CANNOT BE HELD RESPONSIBLE FOR USERS POSTS AND LINKS

... Copyright © 2003-2999 Sonsivri.to ...
Powered by SMF 1.1.18 | SMF © 2006-2009, Simple Machines LLC | HarzeM Dilber MC