|
|
avralam
Active Member
 Offline
Posts: 140
Thank You
-Given: 153
-Receive: 30
|
 |
« Reply #1 on: September 03, 2007, 06:02:52 18:02 » |
|
For ´special paper´ U can use example thickness sheets from old Elfa catalog. Or any paper partially glossy , partially mat. And from old magazines too. Tested : laser printer LBP-810 , iron Tefal in maximum temperature. Time ironing 2-3 min, no press hard.
0,25 mm TTSOP package for CY27EE16 can use, no problem.
|
|
|
|
|
Logged
|
|
|
|
|
cae
Guest
|
|
« Reply #2 on: September 06, 2007, 12:27:39 00:27 » |
|
I have tried all types of media for laser iron on method, and by far the best results obtained are with Press-N-Peel PCB transfer film (PNP-BLUE).
Have done many fine trace SMD boards with this product, and not one bad board.
|
|
|
|
|
Logged
|
|
|
|
jezo
Newbie
Offline
Posts: 27
Thank You
-Given: 44
-Receive: 13
|
|
« Reply #3 on: September 07, 2007, 12:10:23 12:10 » |
|
Hallo, I use colored papers for children. This paper is A4 format and has "water" glue from bottom side (like a post stamp). I printing on the glue side. In the end ironing, paper is unstick from pcb very lightly (underwater). Paper is very cheap, but I don't know, if it's reasonable in other countries.
|
|
|
|
« Last Edit: September 07, 2007, 12:15:24 12:15 by jezo »
|
Logged
|
|
|
|
bbarney
Moderator
Hero Member
Offline
Posts: 2429
Thank You
-Given: 405
-Receive: 545
Uhm? where did pickit put my mute button
|
|
« Reply #4 on: September 08, 2007, 04:48:59 16:48 » |
|
Jezo can you tell me more about this paper,it's sound's like it 's ideal for pcb's
|
|
|
|
|
Logged
|
Ever wonder why Kamikaze pilot's wore helmet's ?
|
|
|
|
|
user112
Junior Member
Offline
Posts: 85
Thank You
-Given: 6
-Receive: 139
Salut tuturor(hello to all)
|
|
« Reply #6 on: September 11, 2007, 01:22:00 13:22 » |
|
a few people recomand this paper if you find it http://tinypic.com/ht8jth.jpg |
|
|
|
|
Logged
|
|
|
|
forter
Active Member
Offline
Posts: 139
Thank You
-Given: 1085
-Receive: 28
|
|
« Reply #7 on: September 11, 2007, 02:54:58 14:54 » |
|
I have wrote in thise forum, i am using old photopaper, printing on photo sensitive side. After warming with ordinary iron, place the plate in hot water. 2 minutes and very good plate is ready for FeCl3. Active layer photopaper contain "jelatin" (i don't know English term for it) and in warm water it increse his volume, because we have no problem in seperating a paper from foil.
|
|
|
|
|
Logged
|
|
|
|
user112
Junior Member
Offline
Posts: 85
Thank You
-Given: 6
-Receive: 139
Salut tuturor(hello to all)
|
|
« Reply #8 on: September 12, 2007, 09:25:23 21:25 » |
|
|
|
|
|
|
Logged
|
|
|
|
|
|
|
|
|
